Dr. David Phillips is an Associate Professor of Practice in the Welding Engineering program at The Ohio State University. He has a Bachelor of Science, Master of Science, and PhD in Welding Engineering.?David is a licensed Professional Engineer (P.E.) in Welding Engineering, an International Welding Engineer (I.W.E.), and a Certified Welding Inspector (C.W.I.).?He brings over 20 years of Welding Engineering experience to his classroom, with particular emphasis in the automotive and aerospace industry sectors. In addition to the course that this text book was developed for, David teaches numerous Welding Engineering courses at The Ohio State University, ranging from sophomore to graduate level.

Preface xii

Acknowledgments xiii

1 What is Welding Engineering? 1

1.1 Introduction to Welding Processes 2

2 Arc Welding Processes 4

2.1 Fundamentals and Principles of Arc Welding 4

2.1.1 Fundamentals of an Electric Arc 6

2.1.2 Arc Voltage 7

2.1.3 Polarity 9

2.1.4 Heat Input 10

2.1.5 Welding Position 11

2.1.6 Filler Metals and Electrodes 12

2.1.7 Shielding 12

2.1.7.1 Gas Shielding 13

2.1.7.2 Flux Shielding 13

2.1.8 Weld Joints and Weld Types for Arc Welding 14

2.1.9 Primary Operating Variables in Arc Welding 16

2.1.9.1 Voltage 16

2.1.9.2 Current 16

2.1.9.3 Electrode Feed Rate/Wire Feed Speed 16

2.1.9.4 Welding Travel Speed 17

2.1.10 Metal Transfer Mode 18

2.1.11 Arc Blow 18

2.1.12 Common Arc Welding Defects and Discontinuities 19

2.2 Arc Welding Power Supplies 20

2.2.1 Transformers 20

2.2.2 Generators 21

2.2.3 Important Electrical Elements in Arc Welding Power Supplies 22

2.2.4 Volt]Ampere Characteristic of Arc Welding Power Supplies 26

2.2.5 Duty Cycle 29

2.3 Shielded Metal Arc Welding 30

2.4 Gas Tungsten Arc Welding 38

2.5 Plasma Arc Welding 46

2.6 Gas Metal Arc Welding 49

2.7 Flux Cored Arc Welding 59

2.8 Submerged Arc Welding 62

2.9 Other Arc Welding Processes 67

2.9.1 Electrogas Welding 67

2.9.2 Electroslag Welding 68

2.9.3 Arc Stud Welding 70

Recommended Reading for Further Information 73

3 Resistance Welding Processes 74

3.1 Fundamentals and Principles of Resistance Welding Processes 74

3.1.1 Resistance and Resistivity 74

3.1.2 Current Range and Lobe Curves 77

3.2 Resistance Spot Welding 79

3.3 Resistance Seam Welding 83

3.4 Resistance Projection Welding 85

3.5 High Frequency Welding 88

3.6 Flash Welding 90

Recommended Reading for Further Information 94

4 Solid]State Welding Processes 95

4.1 Fundamentals and Principles of Solid]State Welding 95

4.1.1 Solid]State Welding Theory 95

4.1.2 Roll Bonding Theory 96

4.2 Friction Welding Processes 97

4.2.1 Inertia Friction Welding 99

4.2.2 Continuous Drive Friction Welding 101

4.2.3 Linear Friction Welding 102

4.2.4 Friction Stir Welding 102

4.3 Other Solid]State Welding Processes 106

4.3.1 Diffusion Welding 106

4.3.2 Explosion Welding 109

4.3.3 Ultrasonic Welding 111

Recommended Reading for Further Information 113

5 High Energy Density Welding Processes 114

5.1 Fundamentals and Principles of High Energy Density Welding 114

5.1.1 Power Density 114

5.1.2 Keyhole Mode Welding 116

5.2 Laser Beam Welding 117

5.3 Electron Beam Welding 119

Recommended Reading for Further Information 122

6 Other Approaches to Welding and Joining 123

6.1 Brazing and Soldering 123

6.2 Welding of Plastics 125

6.2.1 Hot Tool (Plate) Welding 126

6.2.2 Hot Gas Welding 128

6.2.3 Implant Induction Welding 128

6.2.4 Ultrasonic Welding 129

6.2.5 Vibration Welding 129

6.3 Adhesive Bonding 130

6.4 Novel and Hybrid Welding Processes 130

6.5 Oxyfuel Welding and Cutting 133

6.6 Other Cutting Processes 137

6.6.1 Plasma Cutting 137

6.6.2 Laser Beam Cutting 137

6.6.3 Air Carbon Arc Gouging 137

Recommended Reading for Further Information 141

7 Design Considerations for Welding 142

7.1 Introduction to Welding Design 142

7.2 Mechanical Properties 143

7.2.1 Yield Strength 143

7.2.2 Tensile Strength 143

7.2.3 Ductility 143

7.2.4 Fatigue Strength 143

7.2.5 Toughness 144

7.2.6 Mechanical Properties—Effect of Temperature 144

7.3 Physical Properties 145

7.3.1 Thermal Conductivity 145

7.3.2 Melting Temperature 145

7.3.3 Coefficient of Thermal Expansion 146

7.3.4 Electrical Conductivity 146

7.4 Design Elements for Welded Connections 146

7.4.1 Joint and Weld Types 147

7.4.2 Joint and Weld Type Selection Considerations 148

7.4.3 Weld Joint Nomenclature—Groove Welds 152

7.4.4 Weld Joint Nomenclature—Fillet Welds 153

7.4.5 Welding Positions 154

7.5 Welding Symbols 155

7.6 Weld Sizing 161

Recommended Reading for Further Information 164

8 Heat Flow, Residual Stress and Distortion 165

8.1 Heat Flow 165

8.2 Fundamentals and Principles of Residual Stress and Distortion 169

8.3 Approaches to Minimizing or Eliminating Distortion 173

Recommended Reading for Further Information 176

9 Welding Metallurgy 177

9.1 Introduction to Welding Metallurgy 177

9.2 The Fusion Zone 180

9.3 The Partially Melted Zone 182

9.4 The Heat]Affected Zone (HAZ) 183

9.5 Introduction to Phase Diagrams 184

Recommended Reading for Further Information 186

10 Welding Metallurgy of Carbon Steels 187

10.1 Introduction to Steels 187

10.2 Steel Microstructures and the Iron]Iron Carbide Diagram 189

10.3 Continuous Cooling Transformation (CCT) Diagrams 194

10.4 Hardness and Hardenability 196

10.5 Hydrogen Cracking 199

10.6 Heat]Affected Zone Microstructures in Steel 200

Recommended Reading for Further Information 202

11 Welding Metallurgy of Stainless Steels 203

11.1 Introduction to Stainless Steels 203

11.2 Constitution Diagrams 204

11.3 Martensitic Stainless Steels 206

11.4 Ferritic Stainless Steels 207

11.5 Austenitic Stainless Steels 209

11.6 Duplex Stainless Steels 214

Recommended Reading for Further Information 216

12 Welding Metallurgy of Nonferrous Alloys 217

12.1 Aluminum Alloys 217

12.2 Nickel]Based Alloys 222

12.3 Titanium Alloys 226

12.4 Copper Alloys 229

12.5 Magnesium Alloys 230

Recommended Reading for Further Information 232

13 Weld Quality 233

13.1 Weld Discontinuities and Defects 233

13.2 Mechanical Testing of Weldments 235

13.2.1 Tensile Testing 235

13.2.2 Ductility Testing 236

13.2.3 Toughness Testing 237

13.2.4 Fatigue Testing 239

13.3 Nondestructive Testing 243

13.3.1 Visual Inspection 244

13.3.2 Liquid Penetrant Testing 244

13.3.3 Magnetic Particle Testing 246

13.3.4 Radiographic Testing 247

13.3.5 Ultrasonic Testing 250

13.4 Introduction to Fractography 252

Recommended Reading for Further Information 254

14 Codes and Standards 255

14.1 Introduction to Standards 255

14.2 AWS D1.1—“Structural Welding Code—Steel” 261

14.2.1 Welding and Welder Qualification 262

14.2.2 Fabrication and Inspection 269

Recommended Reading for Further Information 269

15 Safe Practices in Welding 270

15.1 Electrical Shock 270

15.2 Radiation 270

15.3 Burns 271

15.4 Smoke and Fumes 271

15.5 Welding in Confined Space 271

15.6 Fire and Explosion Danger 271

15.7 Compressed Gasses 272

15.8 Hazardous Materials 272

Recommended Reading for Further Information 272

Index 273

The New copy of this book will include any supplemental materials advertised. Please check the title of the book to determine if it should include any access cards, study guides, lab manuals, CDs, etc.

The Used, Rental and eBook copies of this book are not guaranteed to include any supplemental materials. Typically, only the book itself is included. This is true even if the title states it includes any access cards, study guides, lab manuals, CDs, etc.